Keywords: Density Concrete, Hematite, Heavy Weight Aggregate, Compressive Strength, Silica Fume -----***-----1. 1INTRODUCTION The main aim of this paper is to find a suitable local substitute for the high density iron ore. Heavy weight iron-ore …
the increase of the iron ore ratio from 0% to 20%, while the compressive strength is decreased greatly. The effects of various preparation parameters on the compressive strength of ICHB are in order of briquetting temperature, bituminous coal ratio, carbonization temperature, carbonization time and iron ore ratio. The above research results
Investigation of Compressive Strength of Concrete from Cement and Iron-Ore Tailings Mixture. August 2015; ... In samples F50L25 a good compressive strength was achieved after 28 days of curing ...
1.1 This test method describes a method for determining the crushing strength of fired iron ore pellets and direct-reduced iron. Cylindrical agglomerates and briquettes are not covered by this test method. 1.2 The values as stated in SI units are to be regarded as the standards. The …
The compressive strength of iron ore granules, as . measured from experiments, reflects the capillary . cohesion of primary particles. For smallest amounts of .
Cohesive strength of iron ore granules . By Contreras Rafael Jaimes, Berger ... The strength is measured by subjecting the granules to vertical compression between two plates. ... It is found that the compressive strength scales with capillary cohesion with a pre-factor that is nearly independent of size polydispersity for the investigated ...
The research on whether can iron ore tailing improve the compressive strength of alkali-activated slag ing concrete is conducted. The experiment shows that too little or too much powder from iron ore tailing will reduce the compression strength of alkali activated slag concrete, when powder from iron ore tailing achieving optimal amount, the compression...
The compressive strength of Daxigou siderite iron ore is higher than that of other samples. When the roasting temperature was controlled at 1200 degrees C, the compressive strength is higher.
The effect of iron ore tailings on the consistency of the fresh concrete were studied, as well as the density, compressive strength, flexural strength and splitting tensile strength, of the hardened concrete. The results of the consistency tests on concrete shows that the slump values ranges from 81 to 53[mm] from concrete sample C0 to C4 ...
Uniaxial compressive strength (UCS) is a key physical test relevant to iron ore crusher design and rock geomechanics for mining. Tests are typically performed on intact lengths of NQ, HQ, or PQ diamond drill core and record the maximum axial load sustained at the point of failure.
In the present investigation, boric acid was used in the ball formation of iron ore fines to improve the compressive strength (CS) of fired pellet. Boric acid was used in combination with carboxymethyl cellulose (CMC) and saw dust and the pellets were fired at different firing temperatures from 1000 to 1300 °C. Box–Behnken statistical design was followed for analyzing the CS at different ...
Iron ore tailings (IOT) are the by-products of iron ore beneficiation, and these tailings are disposed of in several tons annually in quarries, landfills, and tailings dams, causing environmental issues. Various researchers have attempted to study the properties of IOT and the use of …
The addition of iron ore tailings enhances the compressive strength and impermeability of UHPC mortars due to the filling effect of IOT and the pozzolanic reaction of part of the finer IOT when the substitution rate is no more than 40%. The replacement ratio of 40% shows the best results, with low permeability and the maximum compressive strength.
To improve the high brittleness of recycled aggregate concrete containing iron ore tailings (TRAC), the feasibility of adding polypropylene fiber (PPF) to TRAC was studied by performing a compression stress–strain curve test, scanning electron microscope characterization, and a freeze–thaw cycle test. The results indicated that PPF had a beneficial impact on reducing the brittleness of TRAC.
iron ore tailings may be utilised for complete replacement for conventional aggregates in concrete. The iron ore tailings aggregates concrete exhibited a good mechanical strength and even in the case of compressive strength, there was an improvement of 11.56% over conventional aggregates concrete. The indirect tensile strength did not
Two different iron ore tailings replaced a natural quartz aggregate in the geopolymers' formulation. The hardened properties assessed were compressive strength, water absorption, apparent density and porosity. Scanning electron microscopy (SEM) and x-ray micro computed tomography (µ-CT) were used to assess the changes in the microstructure ...
Keywords: Iron Ore Tailings, Pozzolana, Compressive Strength, Workability, Regression Models 1. Introduction Nigeria is a fast developing nation blessed with abundant mineral resources. With major economic developments in the country, more minerals are in demand and thereby, increasing the mining activities. Itakpe iron ore deposits in Ajaokuta,
A probable mathematical relationship between (Si/Al) ratio and (Ca/Si) ratio on the compressive strength of an iron ore tailings sample arising out of geopolymeric reactions October 2019 Journal ...
Chelyabinsk Scientific-Research Institute of Metallurgy. Sokolovsko-Sarbaisk Mining and Concentration Combine. Urals Scientific-Research and Design Institute of Mechanical Concentration of Minerals.
Abstract Macro-synthetic fiber-reinforced iron ore tailings ... (NS) replacement in 50 wt% demonstrates no loss in compressive strength and a minor loss of 7.67% in fracture energy, but the incorporation of IOT lowers splitting tensile strength and limit of proportionality, especially the splitting tensile strength with a decrease of 18.50%. ...
Iron ore is a catch-all name that covers a variety of different ores of iron. Compressive strength, depending on the particular ore, can be from, say, 7MPa or even so small that the ore falls ...
percentage of iron ore tailing in the mix. Twenty-eight (28) days compressive strength and indirect tensile strength values of 43.67N/mm 2 and 2.69N/mm 2 respectively, were obtained for concrete when 20% iron ore tailing (IOT) was used, Values comparable to 28days compressive strength and indirect tensile strength values of
In the case of iron ore pellets, which are also brittle, strain rate effects have only been studied by Gustafsson et al., who showed, from experiments in a split Hopkinson bar device and slow compression, that the strength of a sample of iron ore pellets increased about 30% when deformation velocities increased from 10 mm/min to up to 10 m/s ...
This study aims to broaden the application of iron ore tailing (IOT) in geopolymer. Fresh properties, residual strength, mass loss and microstructure evolution of geopolymer prepared by using fly ash as starting material blended with IOT and activated by sodium silicate and sodium hydroxide solutions were investigated after exposure to 3 and 7 heat-cooling thermal cycles at different target ...
(3) The cause for the different effect of drying on compressive strength between the commercial iron ore and reagent hematite seems to be the difference of gangue minerals that exist only in the iron ore and/or that of surface properties because the particle size distribution of reagent hematite and iron ores used is the same.
Abstract: To predict the key performance index (compressive strength) of Iron ore pellets, a prediction model based on Kernel principal component analysis (KPCA) and RBF neural network was proposed. This paper determined the input variable through the analysis of the chain grate machine - rotary kiln - ring cold pellet production process, deal with the sample data and simplified the model ...
پست الکترونیک: [email protected]
تلفن: 0086-21-58386256
نشانی: شماره 1688، جاده شرقی گاوک، منطقه جدید پودونگ، شانگهای، چین.
کپی رایت © 2021.cryptod تمامی حقوق محفوظ است.نقشه سایت